DIN Rail Input Loop-Powered Isolators

DRSL-LPI_Series

查看下面所有型号

下单

1 Channel (DRSL-LPI-1) or 2 Channel (DRSL-LPI-2) Input Loop Powered Isolators
Powered by the Analog Input Current Signal Loop
1:1 Signal Ratio
Low Input Voltage Drop
Fast Response Time <5 ms
High Conversion Accuracy, <0.1% of Span (0 to 20.5 mA)
Slimline 6 mm (0.24") Housing

过程测量和控制仪器 - 查看相关产品

产品描述

The DRSL-LPI Series DIN rail input loop powered isolators provide a competitive choice in terms of both price and technology for galvanic isolation of current signals to SCADA systems or PLC equipment. These units provide isolation and 1:1 conversion of standard current signals and are powered by the analog input current signal loop.

The DRSL-LPI series offers isolation between input and output, provides surge suppression and protects control systems from transients and noise. These units also eliminate ground loops and can be used for measuring floating signals. Low power consumption facilitates DIN rail mounting without the need for any air gap. Measurement ranges are factory calibrated. These isolators operates over a wide temperature range from -25 to 70°C (-13 to 158°F).

SPECIFICATIONS
NUMBER OF CHANNELS
    DRSL-LPI-1: 1
    DRSL-LPI-2: 2
CURRENT INPUT
Signal Range (Input to Output): 0 to 20.5 mA
Signal Conversion: 1 to 1
Functional Range: 0 to 23 mA (NAMUR NE43 compliant)
Start up Current: 10 µA typical
Input Overload: 50 mA max
Input to Output Voltage Drop: 1.25V + (0.015 x Vout) where Vout = Iout x Routput, typical
Input Voltage Drop: (Unit voltage drop) + Vout
CURRENT OUTPUT
    Output Load: 600Ω max
    Output Load Stability: <0.01% of span/100 Ω (span = 0 to 20 mA)
    Voltage Limit: 17.5V

GENERAL
Internal Consumption: 30 mW per channel
Isolation Voltage (Test): 2.5 kVac
Isolation Voltage (Working): 300 Vac
Signal/Noise Ratio: >60 dB
Cut-Off Frequency (3 dB): 100 Hz
Response Time (0 to 90%, 100 to 10%): <5 ms
Absolute Accuracy (at 25°C): ≤±10 µA + 0.05% of max value of selected span
Temperature Coefficient: ≤±2 µA/°C
EMC Immunity Influence: <±0.5% of span
Extended EMC Immunity NAMUR NE 21, A Criterion, Burst: <±1% of span

ENVIRONMENTAL
Operating Temperature: -25 to 70°C (-13 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Calibration Temperature: 20 to 28°C (68 to 82°F)
Relative Humidity: 0 to 95% RH non-condensing
Protection Degree: IP20
Installation Area: Pollution degree 2 and measurement/overvoltage category II

MECHANICAL
Dimensions: 113 H x 6.1 W x 115 mm D (4.4 x 0.24 x 4.5")
Weight: 70 g (0.15 lb) approx
DIN Rail Type: DIN EN 60715 - 35 mm
Wire Size: 0.13 x 2.5 mm²/AWG 26 to 12 stranded wire
Screw Terminal Torque: 0.5 Nm

订购所有价格均为人民币税前价格，不包括13%增值税和运费！(指定型号)

产品编号产品描述

数量

产品描述

DRSL-LPI-1

¥1,201.23

货期: 2 周

DIN rail input loop-powered isolator, 1 channel

DRSL-LPI-2

¥1,715.73

货期: 2 周

DIN rail input loop-powered isolator, 2 channel

Accessories

RAIL-35-1

¥146.04

货期: 2 周

35 mm (1.4") DIN rail, 1 m (3.3') length

DRSL-MOD-STOP

¥60.43

货期: 5 周

Module stop (screwed onto DIN rail to support and hold mounted devices)

† 所有金额以RMB显示
订购示例: (1) DRSL-LPI-1 DIN rail input loop-powered isolator, 1 channel, ¥1,201.23 plus (1) DRSL-MOD-STOP Module stop (screwed onto DIN rail to support and hold mounted devices), ¥60.43 plus (1) RAIL-35-1 35 mm (1.4, ¥146.04, ¥1,201.23 + 60.43 + 146.04 = ¥1,407.70

产品手册:

下载 Installation Guide for Signal Conditioners

下载 DIN Rail Loop Powered Isolators

相关产品: