RTD Input Non-Isolated DIN Rail Loop-Powered Signal Conditioner

DRSL-RTD-LP

^¥1,013.21 DRSL-RTD-LP

下单

2, 3 or 4-Wire Pt100 RTD Input
Powered By the Host (Output) Current Signal Loop
High Accuracy Better Than 0.2°C or 0.1% of Selected Range
Slimline 6 mm (0.24") Housing
Excellent EMC Performance and 50/60 Hz Noise Suppression
Fast Response Time < 30 ms/300 ms (Selectable)
Pre-Calibrated Temperature Ranges Selectable via DIP-Switches

过程测量和控制仪器 - 查看相关产品

产品描述

The DRSL-RTD-LP RTD input non-isolated DIN rail loop-powered signal conditioner measures a standard 2-, 3- or 4-wire Pt100 temperature sensor and provides a passive analog current output signal. The DRSL-RTD-LP provides a competitive choice in terms of both price and technology for interfacing RTD signals to SCADA systems or PLC equipment. This unit is powered by the host (output) current signal loop. Low power consumption facilitates DIN rail mounting without the need for any air gap. Easy configuration of more than 1000 factory calibrated measurement ranges is done via DIP-switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).

SPECIFICATIONS
INPUT
Input Type: 2, 3, or 4-wire Pt100 RTD
Temperature Range: -200 to 850°C (-328 to 1562°F)
Sensor Current, RTD: <150 µA
Sensor Cable Specifications: 50Ω per wire or 50 nF
Effect of Sensor Cable Resistance (3 or 4-Wire RTD): <0.002Ω/Ω
Broken Sensor Detection: >800Ω
Shorted Sensor Detection: <18Ω

OUTPUT
Current Output
Programmable Signal Ranges: 0 to 20 mA and 4 to 20 mA
Range Limits (NAMUR NE43 Out of Range): Below 3.8 mA or above 20.5 mA
Sensor Error Detection (Dip Switch Selectable for Enable or None): Below 3.5 mA or above 23 mA
Incorrect DIP-Switch Setting Identification: Below 3.5 mA or above 23 mA
Output Error Level: DIP switch selectable for upscale or downscale
Load Resistance (Ω): ≤(Vsupply -3.3)/ 0.023
Load Stability: ≤0.01% of span/100Ω

GENERAL
Supply Voltage: 3.3 to 35 Vdc
Voltage Drop: 3.3 Vdc
Power Consumption: 1 W max
Internal Consumption: 0.65 W max
Signal/Noise Ratio: >60 dB
Response Time (0 to 90%, 100 to 10%): <30 ms/300 ms (selectable, provides either fast response or signal dampening as needed).
Accuracy: Better than 0.2°C or ±0.1% of selected range
Temperature Coefficient: ≤±0.02°C/°C
EMC Immunity Influence: <±0.5% of span
Extended EMC Immunity
NAMUR NE 21, A Criterion, Burst: <±1% of span (span = selected input range)

ENVIRONMENTAL
Operating Temperature: -25 to 70°C (-13 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Calibration Temperature: 20 to 28°C (68 to 82°F)
Relative Humidity: 0 to 95% RH non-condensing
Protection Degree: IP20
Installation Area: Pollution degree 2 and measurement/overvoltage category II

MECHANICAL
Dimensions: 113 H x 6.1 W x 115 mm D (4.4 x 0.24 x 4.5")
Weight: 70 g (0.15 lb) approx
DIN Rail Type: DIN EN 60715 - 35 mm
Wire Size: 0.13 x 2.5 mm²/AWG 26 to 12 stranded wire
Screw Terminal Torque: 0.5 Nm

订购所有价格均为人民币税前价格，不包括13%增值税和运费！(指定型号)

产品编号产品描述

数量

产品描述

DRSL-RTD-LP

¥1,013.21

货期: 2 周

RTD input non-isolated DIN rail loop-powered signal conditioner

Accessories

RAIL-35-1

¥146.04

货期: 2 周

35 mm (1.4") DIN rail, 1 m (3.3') length

DRSL-MOD-STOP

¥60.43

货期: 5 周

Module stop (screwed onto DIN rail to support and hold mounted devices)

† 所有金额以RMB显示
订购示例: (1) DRSL-MOD-STOP Module stop (screwed onto DIN rail to support and hold mounted devices), ¥60.43 plus (1) DRSL-RTD-LP RTD input non-isolated DIN rail loop-powered signal conditioner, ¥1,013.21 plus (1) RAIL-35-1 35 mm (1.4, ¥146.04, ¥60.43 + 1,013.21 + 146.04 = ¥1,219.68

产品手册:

下载 Installation Guide for Signal Conditioners

下载 DIN Rail Isolators and Signal Conditioners