Programmable Stepper Drive with Integrated Power Supply

Si3540

Programmable Stepper Drive

查看下面所有型号

下单

3.5 A, 40 Vdc
110/220 Vac Input, 50/60 Hz Switch Selectable
Microstepping 2000 to 50,800 Steps/Rev
Idle Current Reduction Software Selectable: 0, 25, 50, or 100%
Software Selectable Motor Current 0.2 to 3.5 A/Phase
Eight Optically Isolated Inputs 5 to 24 Vdc
Three Optically Isolated Outputs 12 to 24 Vdc, 100 mA max
One Optically Isolated Output 5V, Dedicated to Fault Out
Download, Store and Execute Programs Using Si Programmer (Free Download)
Mating Connectors Included
Sample Motion Programs Available by Request

驱动器和发动机 - 查看相关产品

产品描述

The Si3540 is a programmable step motor drive/indexer packaged in a rugged steel and aluminum enclosure. Integral power supply, heat sink, mounting brackets, switch covers and connectors are included with each Si3540. The Si3540 comes with all operating software necessary to create a complete step motor-based motion control solution.

The Si3540 includes Applied Motion Products' Windows-based Si Programmer™ software application for quick set up and ease of use. Si Programmer™ is ideal for stand-alone operation. For users with software development expertise, the Si3540 can also be used with Applied Motion's Si™ Command Language (SCL). SCL allows for control of an Si drive, like the Si3540, via serial commands sent from a host device such as a PC or PLC. This permits the user to perform a variety of motion, I/O, and system status tasks via a host serial device.

Multiple axis applications can be handled with the SiNet™ Hub Programmer software, which gives you the ability to control up to 4 "Si" or "i" drives, stepper and servo, from just one SiNet™ Hub 444. Not only can you sequence up to four motors, but a SiNet™ Hub 444 also has access to the inputs and outputs of all the drives connected to it, providing your program with up to 32 inputs and 12 outputs. In addition, the Hub 444 provides 4 digital inputs and 4 digital outputs of its own. You can also use Applied Motion's MMI-01 to interface the drives with the machine operator.

Factory set to operate at 110 VAC input, the Si3540 can be set by the user to operate at 220 VAC input by a simple switch selection.

Pluggable screw terminal blocks are provided for the I/O, motor, and AC power input. Mating connectors, programming cable with computer interface connector, as well as all operating software are provided with each Si3540 drive.

The Si3540 is both CE and TUV compliant.

Si Programmer
Intended for use in stand-alone applications, Si (Simple Indexer) Programmer provides quick, out-of-the-box use with an extremely friendly, point-and-click graphical interface that does not require any software programming experience. Once an Si program has been constructed and downloaded to the drive, the program can be executed stand-alone at power-up or from an external trigger. Constructing a program is accomplished through the use of instructions selected in a point-and-click manner. Once an instruction is selected, a "fill in the blanks" format is used to input parameters.

Constructing an Si program requires no prior programming experience nor does it require learning a programming language. Si Programmer generates the actual motion control program, based on user selected parameters, thereby eliminating syntax errors. Once created, programs are easily downloaded, uploaded, saved and printed.

Si Programmer also provides the capability to control digital inputs and outputs, useful for interfacing with external equipment like PLCs, sensors, end-of-travel switches, and more. Si Programmer has found success in all types of applications, from simple linear actuator applications to complete machine control with operator interface applications.

NOTE: Power cord not included. See Accessories below to order.

订购所有价格均为人民币税前价格，不包括13%增值税和运费！(指定型号)

其他客户同时购买: 这个图标可以点击扩大，跳出的清单包括了其他客户在购买此产品时同时购买的其它产品。

产品编号产品描述

数量

产品描述

Si3540

咨询

货期:

Programmable step motor drive with integral power supply

Recommended Motors

OMHT17-075

¥984.27

货期: 12 周

NEMA 17, 62.8 oz-in holding torque

OMHT17-275

¥723.90

货期: 6 周

NEMA 17, 62.3 oz-in holding torque

OMHT17-278

¥856.09

货期: 4 周

NEMA 17, 113 oz-in holding torque

OMHT23-393

咨询

货期:

NEMA 23, 76.6 oz-in holding torque

OMHT23-593

¥856.09

货期: 6 周

NEMA 23, 79.3 oz-in holding torque

OMHT24-100

¥961.38

货期: 6 周

NEMA 24, 123 oz-in holding torque

OMHT23-397

咨询

货期:

NEMA 23, 177 oz-in holding torque

OMHT23-597

¥950.51

货期: 10 周

NEMA 23, 177 oz-in holding torque

OMHT23-400

咨询

货期:

NEMA 23, 264 oz-in holding torque

OMHT23-600

¥1,402.01

货期: 2 周

NEMA 23, 264.8 oz-in holding torque

Accessories

HUB 444 DIN RAIL

咨询

货期:

Multi-axis network hub with DIN rail mounting kit

MMI-01

咨询

货期:

Operator Interface

OM-CONV-USB

¥214.02

货期: 库存

USB to RS232 Interface Converter; USB-A to DB9-male

Power Cord-SE

¥108.31

货期: 5 周

AC Power cord with stripped end termination

Power Cord-SE-M16

¥144.78

货期: 2 周

8' Power cord with M16 cable gland strain relief, 3x16 AWG, 250Vac max.

SI-PROG-CBL

¥263.13

货期: 4 周

Replacement programming cable (comes with drive)

DRIVE-CBL

咨询

货期:

Replacement MMI and/or HUB communications cable (comes with MMI-01 and HUB 444)

DSUB-9-MF

咨询

货期:

DIN rail interface module, 9-pin

DSUB-9-MF-CBL

¥404.13

货期: 2 周

DSUB cable, 9-pin, 2 m (6.6'), male/female connectors

† 所有金额以RMB显示
注: Programming cable and mating connectors are included. Programming software is a free download; click on "Software" icon below the picture. To see torque-speed curves for recommended motors, click on "Specs" above.
订购示例: (1) OM-CONV-USB USB to RS-232 Interface Converter, ¥214.02

产品手册:

下载 Si3540 Series - Programmable Step Motor Driver Hardware Manual

下载 STM, ST, Stac6, 1240i, 3540i, si3540 Series - Si Command Language (SCL) for Stepper Drives